Ask Dr. Dave / Columns

Ask Dr. Dave

September 1, 2004
/ Print / Reprints /
ShareMore
/ Text Size+
September 2004

Dr. Dave Dunn


QUESTION: Can you recommend a method for bonding aluminum to aluminum for use in a marine (salt water) environment? We are currently using anodized aluminum with a two-part epoxy or reactive acrylic adhesive. Both adhesives have good initial bond strength, but the bond degrades with exposure to salt water. The bonded parts (small sailboat rudders) are not subject to large loads and do not need to withstand more than moderate abuse. However, longevity is a concern. A useful life of about 10 years is required.

ANSWER: All adhesives will lose strength upon immersion in water. Water acts in two ways on a bonded assembly - it can be absorbed into the adhesive and soften it, and it can degrade the interface between the adhesive and the bonded surfaces. You should ensure that the samples have dried out thoroughly when you test after the water immersion; you may find that much of the initial strength has been retained. Secondly, you should talk to your adhesive supplier and ask for the best adhesive for long-term water immersion. General-purpose two-part epoxies are easy to use but do not typically give the highest performance when cured at room temperature. You may have to use heat curing to get the best performance. Also, the organosilane primers commonly used for bonding metals to glass will often give improved water resistance with both epoxies and reactive acrylics when used to bond metals. You should also examine whether it is possible to protect the bond line from water. If you can seal it with a moisture-resistant sealant such as a silicone or polysulfide, this should provide additional protection for the bond.

QUESTION: We are a company specializing in backyard multi-sports courts. We are bonding putting green turf to a free-form concrete pad and we are not too excited with the product that we are currently using. One of the turfs has a cushion backing approximately 1/4" thick that would provide an ideal surface for bonding. The second turf is a woven-type backing about 1/16" thick, and there is no cushion effect. Please advise us on suitable adhesives.

ANSWER: Many adhesives have been used for this type of application, including neoprene contact cements, natural rubber latex and EVA latex. However, for maximum outdoor durability, a crosslinked acrylic latex is probably the best product choice. Experiment and make sure you get good wetting and penetration of the fibers. It is very important that your concrete slab be fully cured, clean and dry before applying the adhesive to it. Make sure that you follow the adhesive manufacturer's instructions closely on application methods and use the correct drying time of the adhesive before assembling the bond. Also, take care to roll the turf in place rather than dropping it; this will ensure maximum contact of the adhesive with the turf and eliminate any air pockets.

Questions for publication should be directed to Dr. Dave Dunn at 242 Trails End, Aurora OH 44202; phone (330) 562-2930; fax (253) 681-8460; e-mail DrDave242@att.net ; or visit http://www.fldenterprises.com .

Did you enjoy this article? Click here to subscribe to Adhesives & Sealants Industry Magazine.

You must login or register in order to post a comment.

Multimedia

Videos

Image Galleries

ASI April 2014 Photo Gallery

Our April 2014 issue is now available!

Podcasts

ExxonMobil Tackifier Expansion

Dwight Tozer, vice president of ExxonMobil’s Adhesion Industry business, discusses the company’s latest tackifier expansion project with Editor-in-Chief Susan Sutton.

More Podcasts

Adhesives & Sealants Industry Magazine

ASI July 2014 cover

2014 July

Our annual Distributor Directory helps you locate a distributor that best suits your needs. Check it out today!

Table Of Contents Subscribe

THE ADHESIVES STORE

handbook-sealant-tech.gif
Handbook of Sealant Technology

The Handbook of Sealant Technology provides an in-depth examination of sealants, reviewing their historical developments and fundamentals, adhesion theories and properties, and today’s wide range of applications.

More Products

ASI 2014 Buyers GuideASI's Buyers' Guide

Annual purchasing resource for equipment used in the manufacture/formulation of adhesives, sealants, pressure sensitives, tapes and labels and for application of finished adhesives. 

Clear Seas Research

With access to over one million professionals and more than 60 industry-specific publications, Clear Seas Research offers relevant insights from those who know your industry best. Let us customize a market research solution that exceeds your marketing goals.

STAY CONNECTED

facebook_40px twitter_40  youtube_40pxlinkedin_40 google+ icon ASI 30px