Styrene Isoprene Butadiene (SIBS) Block Copolymers Improve PSA Label Adhesive Performance

October 1, 2007
/ Print / Reprints /
ShareMore
/ Text Size+


Figure 1. SIBS Polymer Chemistry

Styrenic block copolymers (SBCs) used in pressure-sensitive adhesives (PSAs) for labeling are crucial to formulating adhesives with the desired balance of tack, peel and shear adhesion. Applications that require PSAs with better clarity, improved low-temperature performance, lower gels (in the case of hot-melt adhesives), and better economics challenge formulators to develop the best performing and highest value products. PSA label adhesives must also exhibit the proper adhesion to a suitable release liner, as well as provide clean, efficient die cutting, which allows for easy and clean removal of the unwanted label matrix. To address these needs, Kraton Polymers has developed SIBS-based polymers for use in PSAs and, specifically, polymer MD6465BT for label applications.

SIBS polymers, like other styrene block copolymers, consist of block segments of styrene monomer and rubber monomer units. However, these polymers also contain an unsaturated elastomer, or rubber unit, consisting of isoprene and 1,3-butadiene. Figure 1 illustrates the mixed chemical mid-block of SIBS polymers. It is important to note that the unique polymerization process used to manufacture these polymers can yield both linear and radial polymer structures useful for tailoring polymers to specific performance requirements.

Preferred Label Polymer Properties

Preferred SBC label polymers have properties that provide significant adhesive formulating flexibility, such as low viscosity and acceptable strength, and can be easily tackified to yield efficiently die-cut adhesives. Polymers with high melt flow rates, a radial structure, low styrene and high diblock content are most often used to meet these requirements. The typical physical properties of Kraton MD6465BT are listed in Table 1.

Characterizing the viscoelastic properties of a polymer can provide valuable insight into formulating adhesives with the desired properties. A key reason why SBCs have not been used as neat polymers in adhesive applications is that the compliance of the material (J, J = 1/G) is too low to conform to the bonding surface on a microscopic level. To develop adhesion, molecular distances between the adhesive and substrate must reach an interatomic distance of less than 1 nanometer. Dahlquist has theorized that the modulus of a material must be less than 3.3 105 Pa to adhere to a surface.

Adding low-molecular-weight materials that are compatible with the rubber mid-block phase can reduce the SBC’s modulus. Modulus reduction is accomplished by two effects: lowering the styrene content of the mixed system, and plasticizing and swelling of the rubber phase, which leads to a decrease in physical crosslink. However, simply lowering the modulus to a value less than 3.3 105 Pa by the addition of a compatible plasticizer, such as process oil, does not develop adhesion. It is found that an oiled SBC will form an intimate association with a substrate, but the bonding force is too small, and the polymer system is easily removed. To develop tack and adhesion at room temperature, the internal viscosity and resistance to peel of the elastomeric phase must be increased. Specifically, the glass-transition temperature (Tg) of the elastomeric phase must be increased from the values of the pure elastomer (isoprene = -58°C/-72°F, butadiene = -84°C/-119°F) to values between -10°C/14°F and 10°C/50°F. This is accomplished by adding tackifying resins.

Figure 2. SIBS Viscoelastic Properties

Figure 2 demonstrates the tan delta and storage modulus curves of MD6465BT and a comparable styrene isoprene styrene (SIS) polymer. MD6465BT has a lower Tg due to the presence of butadiene in its mid-block. MD6465BT also has a higher storage modulus (G’), but one low enough to make PSAs with desirable properties.

Figure 3. Polymer - Resin Solubility Parameters

Tackifying SIBS Polymers

Since SIBS polymers are styrenic block copolymers, tackifying resins and other additives have an affinity for either of the two phases with which to interact. SIBS polymers have two glass-transition temperatures - an upper (about 100°C for the polystyrene domains) and a lower (about -73°C for the isoprene-butadiene mid-block). SIBS polymers can be effectively tackified using resins from any of the major resin categories, such as aromatic modified C5 hydrocarbons, partially and fully hydrogenated hydrocarbons, rosin esters (gum, wood, and tall oil derivatives), and modified terpenes.

Hildebrand solubility parameters for various polymer materials and the tackifying resin groups that are compatible with them are identified in Figure 3. As the solubility parameter for SIBS polymers’ elastomer phase, isoprene–butadiene midblock, is slightly higher (8.3) than that of the isoprene mid-block of SIS polymers (8.1), we suggest tackifying resins that contain a higher aromatic content. For example, to effectively tackify SIBS polymers using modified C5 hydrocarbon resins, those resins having an aromatic content of >10% (preferably >15%) are suggested for pressure-sensitive adhesives.

Figure 4 (top). Adhesive Viscosity Retention

Figure 5 (bottom). Low-Temperature RBT

Thermal Stability

There is an important difference in the mechanism of degradation between SBS and SIS polymers. SBS polymers can degrade by crosslinking in the mid-block. A formulation containing a high concentration of an SBS polymer, and held at high temperature in a mixer or holding tank for an excessive period of time, may form gel particles as degradation occurs and generally increases in viscosity. SIS polymers degrade by chain scission of the polyisoprene chain. A formulation based on an SIS polymer degraded at high temperature will show a loss in melt viscosity, but no gel will form.

Because of their unique isoprene/butadiene mid-block chemistry, adhesives formulated with SIBS polymers are less subject to viscosity change during prolonged heat conditions. SIBS polymers can be mixed similar to conventional mid-block polymers, and the same level of care and good manufacturing practices should be followed. Figure 4 shows the viscosity retention in percent for hot-melt adhesive formulations containing polymer, hydrocarbon tackifying resin, naphthenic oil and antioxidant based on SIBS and SIS polymers. As demonstrated, SIBS polymers show excellent viscosity retention during heat aging.

Although many antioxidants work well and are suitable for use with SIBS polymers, Irganox® 1726 (4,6-bis [dodecylthiomethyl]-o-cresol), manufactured by Ciba Specialty Chemicals, is an exceptional antioxidant for these polymers. It is particularly effective in preventing polybutadiene gels and in retarding color generation. Antioxidant levels of 0.3-0.5% are usually sufficient for typical hot-melt applications.

Adhesive Formulations and Performance

MD6465BT will find use in PSA label adhesives ranging from high-tack permanent adhesives to lower-tack removable and specialty-type labels. Table 2 shows formulations (based on material weight percent) using MD6465BT for removable, permanent and low-temperature adhesives. The tackifying resins used are manufactured by Cray Valley.

Note that for these formulations the same materials were used at different material percentages. This type of formulating flexibility can help reduce raw-material inventories and provide improved operations efficiency. Table 3 lists typical test methods used in measuring adhesive performance.  

Maintaining tack at low temperatures is critical in refrigerated and freezer label applications. PSAs using MD6465BT can be formulated to produce adhesives with superior low-temperature tack. Figure 5 shows that a 5-10°C improvement in low-temperature rolling ball tack can be expected using MD6465BT over a comparable SIS polymer. Most adhesives at lower temperatures become less tacky, which requires the use of specialty additives to achieve the necessary adhesive performance. MD6465BT, with its superior low-temperature performance, offers formulators to use fewer of these more-expensive additives, such as liquid tackifying resins.

Formulators often choose to blend SIS and SBS with SB polymers for improved economics. However, SIS polymers have limited compatibility with SBS and SB polymers in many formulations. SIBS polymers offer improved compatibility with SBS and SB polymers over conventional SIS polymers. This additional level of compatibility can help improve adhesive formulation performance. Specifically, when compared to SIS polymers, SIBS polymers:
  • Accept higher levels of SBS polymer for improved economics and still maintain critical PSA performance properties.
  • Produce adhesives with better heat stability and reduced gel content.
  • Produce formulations with significantly improved clarity.


Table 4 shows the typical materials (wt. %) and performance properties for label adhesives based on MD6465BT and a comparable SIS polymer. As shown, MD6465BT, as the only polymer and in SB blended polymer systems, provides improved clarity and tack levels while maintaining excellent adhesion during difficult mandrel testing. (Mandrel testing is a measure of an adhesive's ability to resist lifting [flagging] from curved surfaces such as small-diameter containers.) For this test, a polypropylene rod measuring 1 cm in diameter was used with labels measuring 1.5 cm by 0.5 cm. Edelex® N956 naphthenic oil is manufactured by Shell Chemical Co.

Conclusion

In conclusion, SIBS polymers, when formulated for PSA label applications:
  • Provide an excellent balance of tack, peel and shear adhesion.
  • Create value and offer economical formulating latitude and compatibility with diverse ranges of formulating materials including tackifying resins, plasticizers, fillers, and additives.
  • Yield a dual mechanism of chain scission and crosslinking that results in hot-melt formulations with improved viscosity stability due to their isoprene and butadiene midblock.
  • Provide superior tack at lower temperatures for demanding refrigerator and freezer applications.
  • Yield high-clarity adhesives when formulated with SIS, SBS and SB polymers.
For more information on polymers, visit www.kraton.com.

Did you enjoy this article? Click here to subscribe to Adhesives & Sealants Industry Magazine.

You must login or register in order to post a comment.

Multimedia

Videos

Image Galleries

ASI April 2014 Photo Gallery

Our April 2014 issue is now available!

Podcasts

ExxonMobil Tackifier Expansion

Dwight Tozer, vice president of ExxonMobil’s Adhesion Industry business, discusses the company’s latest tackifier expansion project with Editor-in-Chief Susan Sutton.

More Podcasts

Adhesives & Sealants Industry Magazine

ASI Sept 2014 cover

2014 September

Our September issue features articles focusing on high-tech applications and raw materials, as well as a preview of the ASC Fall Convention and Expo. Check it out today!

Table Of Contents Subscribe

THE ADHESIVES STORE

handbook-sealant-tech.gif
Handbook of Sealant Technology

The Handbook of Sealant Technology provides an in-depth examination of sealants, reviewing their historical developments and fundamentals, adhesion theories and properties, and today’s wide range of applications.

More Products

ASI 2014 Buyers GuideASI's Buyers' Guide

Annual purchasing resource for equipment used in the manufacture/formulation of adhesives, sealants, pressure sensitives, tapes and labels and for application of finished adhesives. 

Clear Seas Research

With access to over one million professionals and more than 60 industry-specific publications, Clear Seas Research offers relevant insights from those who know your industry best. Let us customize a market research solution that exceeds your marketing goals.

STAY CONNECTED

facebook_40px twitter_40  youtube_40pxlinkedin_40 google+ icon ASI 30px