- THE MAGAZINE
- INFO FOR...
- ASI Store
- ASI Top 25
- ASI End User
- Classifieds and Services Marketplace
- Product & Literature Showcases
- List Rental
- Market Trends
- Custom Content & Marketing Services
- ASI Readers' Choice Awards
Using self-assembled monolayers - essentially molecular wires - and a three-part anti-corrosion strategy, researchers at the Georgia Institute of Technology have made significant advances toward solving those problems. At the 229th national meeting of the American Chemical Society on March 13, the researchers described improvements that could allow ECA materials to conduct electrical current as well as the metal alloy solders they are designed to replace.
The research has been sponsored by the National Science Foundation, the U.S. EPA and several electronic interconnect companies.
"In certain applications that require high current densities, conductive adhesives still do not measure up to metallic solders," said C.P. Wong, a Regents Professor at Georgia Tech's School of Materials Science and Engineering. "However, by using these self-assembled molecular wires and controlling corrosion at the interface, we can significantly increase the current density."
For environmental reasons, manufacturers are moving away from the tin-lead alloys now used to make the connections for integrating devices into such products as computers, PDAs and cell phones. Japanese manufacturers adopted lead-free electronic interconnection technology in January of this year, and European Union manufacturers are expected to follow suit in June 2006.
Though the United States has no official requirement for halting the use of lead, the European and Japanese decisions have spurred new research into alternative materials. Those alternatives fall into the following two categories.
- Alloys that combine tin with such metals as silver, gold, copper, bismuth or antimony, and
- Conductive adhesives that combine flakes of silver, nickel or gold with an organic polymer matrix.
Each alternative has its own set of advantages and disadvantages.
Conductive adhesives could simplify electronics manufacturing by eliminating several processing steps, including the need for acid flux and cleaning with detergent and water. Because the materials can be cured at lower temperatures - about 150°C, and possibly even room temperature - they would produce less thermal stress on components, require less energy, and use existing circuit board materials.
"Conductive adhesives have a lot of advantages, but there are a few challenges," Wong said. "After you attach a component to a board with conductive adhesives and then cure it, you must test the connections under conditions of high humidity and heat. When you do that, electrical resistance in the joints increases and conductivity drops. That is a major problem for the industry."
At first, scientists and engineers believed the problem was caused by oxidation. But Wong and colleagues at the National Science Foundation-supported Microsystems Packaging Research Center showed that galvanic corrosion, caused by contact between dissimilar metals in the adhesive and tin-lead alloys used in device contacts, was the real culprit. They have since published numerous papers describing strategies for fighting corrosion.
"By understanding this galvanic corrosion, we can develop improved materials that use an inhibitor such as acid to protect the contacts from corrosion, and we can use an oxygen scavenger such as hydroquinone to grab the oxygen required for corrosion to take place," Wong said. "We can also include a sacrificial material with a lower potential metal that is attacked by the corrosion process first, thus sparing the conductive materials."
Further improvements were made by substituting short-chain dicarboxylic acids for the surfactant stearic acid, used to prevent agglomeration of the silver flakes. Replacing or reducing the stearic acid - which acts as an insulator around the silver flakes - further improved current flow.
Still, the current density provided by conductive adhesives fell short of what's needed to support power-hungry devices like processors.
"Recent studies show that, with incorporation of these self-assembled monolayers, the electrical conductivity and current-carrying capability of conductive adhesives could compete well with traditional solder joints," Wong said. "This could be a significant advance in improving these materials."
But like many advances, the SAM structures aren't yet optimized. Testing shows that they begin to decompose at temperatures above 150°C.
"We need additional research in this area to develop more stable materials that are still able to carry the current density required and have the necessary mechanical properties," said Li, a graduate student in Wong's laboratory.
Georgia Tech has applied for patents on the self-assembled monolayer, and on the techniques for controlling corrosion.
For more information, contact Professor C.P. Wong, School of Materials Science & Engineering, Georgia Institute of Technology, 771 Ferst Drive, Atlanta, GA 30332-0245; phone (404) 894-8391; fax (404) 894-9140; or e-mail firstname.lastname@example.org.