Honda Installs Seam-Sealing System to Increase Productivity and Flexibility

March 20, 2003
/ Print / Reprints /
ShareMore
/ Text Size+
When Honda Motor Co. converted its sealing robots, not only were quality and appearance improved, but the company was also able to perform additional sealing at the same cycle time.

The seam-sealing system is customized to ELP’s specifications, making the system easy to use and maintain.
In 1998, Honda Motor Co. initiated a strategy to dramatically increase the flexibility of its plants to produce new models in response to worldwide customer demand. Timed to coincide with the synchronous launch of the totally redesigned 2001 Honda Civic, the new manufacturing system made major equipment and layout changes in 11 plants around the world where the Civic is built, including Honda of America Mfg.’s (HAM) auto plant at East Liberty, Ohio.

While the innovations at the East Liberty Plant (ELP) focused largely on the weld and assembly departments, each supporting department was asked to look for ways to increase productivity and flexibility. In the paint department, the engineering team identified downtime caused by plugged tips on sealer guns as an area for improvement. Its top equipment evaluation criteria were safety/ergonomics, quality, delivery and cost effectiveness.

The PrecisonSwirl has eliminated the beads from sliding on vertical surfaces and significantly reduced brushing.
In January 2000, the paint department project team led by Derek Heath, engineering staff, and Jim Naderer, engineering coordinator, began a feasibility study on Graco’s PrecisionFlo and PrecisionSwirl seam-sealing system. Tests using the PrecisionFlo/Swirl system at Graco’s laboratory in Detroit and confirmed by ELP’s own lab indicated the system would provide a consistent, uniform ribbon of sealer that reduced manual brushing and sealer usage. The multi-directional swirl pattern would also reduce cycle and programming time.

On-line tests were successful. Within five months, ELP’s sealing robots were converted to the PrecisionFlo system with PrecisionSwirl applicators on each robot.

Sealing the seams on the underbody.

Quality, Appearance Improved

“The most obvious improvement is quality,” said Heath. “Our old process featured a low-pressure system that laid the bead on the seam. In certain areas, the bead would not stay on the seam, or it would slide on vertical surfaces. We had to pay special attention to these seams in the brushing area.

“Our new system lets us adjust the applicator’s rotational speed, standoff distance and flow rate for greater control and for better penetration on irregularly shaped parts,” Heath continued. “It also provides higher pressures so the bead is injected into the seam, creating a more resilient seal. Subsequently, we’ve reduced the opportunity for water leaks while increasing consistency on the bead profile. This reduces the amount of brush work by associates down the line.”

The electric orbital applicator produces a wide variety of closed circular-loop bead patterns, material thicknesses and pattern widths. The swirl pattern can be applied to horizontal or vertical surfaces, which makes the PrecisionSwirl equipment an effective applicator to seal the many seams on the body of a car.

“General appearance has improved,” Heath adds. “The swirl bead is flat, which blends into the frame and makes it more appealing.”

Naderer explained that they elected to reduce the speed of the robots performing the job. “This cut wear on the robots and the entire system, lowering maintenance and service costs,” he said. “The PrecisionFlo features independent gun controls for different processes, flow rates and pressures, allowing a second gun to be mounted on the robots that seal the wheel wells.”

Sealing the seams on the vertical surface of a wheel well.

Additional Sealing at Same Cycle Time

The 2001 Civic required additional sealing compared to the 2000 model. The increased production capability of the PrecisionSwirl allowed Honda to do the additional work without increasing cycle time. “Ultimately, we were able to address the requirements of the new Civic model without increasing cycle time or adding manpower, robots and equipment,” said Heath.

Jim Naderer (left) and Derek Heath in front of the remote touch screens adjacent to the seam-sealing work area.
Another important feature of the system was the ability to customize the system to Honda’s specifications. Space constraints on the sealer deck made it impossible to mount the entire controller in this area. The solution was to install the controllers on the mezzanine above the production line and mount remote touch screens adjacent to the work area on the sealer deck. “We were able to incorporate the entire new system without re-routing production or traffic through the area,” says Heath.

“Furthermore, it was relatively easy to install the equipment without disrupting production because the system components were modular,” says Naderer. “And, the ease of programming the Swirl pattern significantly reduced robot programming time. This, coupled with the modular equipment, allowed the installation of two or four units on a non-production weekend. Most of the installation and programming were performed by our own engineering team and line associates.”

“It’s a very easy system to monitor and maintain,” says Heath. “In addition, our production downtime due to plugged tips has been virtually eliminated, brushing has been reduced significantly in most areas, material savings have been recognized and the work area is cleaner.”

“As with any new installation of this size, we had some production issues that had to be addressed during installation and startup,” says Naderer. “Graco responded promptly to our needs and worked closely with us to make this system meet our requirements. From an application standpoint, it does exactly what we have programmed it to do.”

Naderer and Heath credit the support they received within the plant to accomplish the project in such a short timeframe.

For more information:

For more information on the PrecisionFlo/PrecisionSwirl seam-sealing system, contact Graco Inc., PO Box 1441, Minneapolis, MN 55440-1441; phone 877-84GRACO; fax 319-395-9816; e-mail info@graco.com; or visit http://www.graco.com.

Did you enjoy this article? Click here to subscribe to Adhesives & Sealants Industry Magazine.

You must login or register in order to post a comment.

Multimedia

Videos

Image Galleries

In-Depth Features

These articles detail advantages and innovations for multiple end uses.

Podcasts

ExxonMobil Tackifier Expansion

Dwight Tozer, vice president of ExxonMobil’s Adhesion Industry business, discusses the company’s latest tackifier expansion project with Editor-in-Chief Susan Sutton.

More Podcasts

THE MAGAZINE

Adhesives & Sealants Industry Magazine

ASI April 2014 cover

2014 April

Our April issue focuses on pressure-sensitive adhesives, including a preview of PSTC's 2014 Tape Summit, as well as converting/packaging and composites!

Table Of Contents Subscribe

THE ADHESIVES STORE

handbook-sealant-tech.gif
Handbook of Sealant Technology

The Handbook of Sealant Technology provides an in-depth examination of sealants, reviewing their historical developments and fundamentals, adhesion theories and properties, and today’s wide range of applications.

More Products

asi1211p_Cover-DE.gifASI's Buyers' Guide

Annual purchasing resource for equipment used in the manufacture/formulation of adhesives, sealants, pressure sensitives, tapes and labels and for application of finished adhesives. 

Clear Seas Research

With access to over one million professionals and more than 60 industry-specific publications, Clear Seas Research offers relevant insights from those who know your industry best. Let us customize a market research solution that exceeds your marketing goals.

STAY CONNECTED

facebook_40px twitter_40  youtube_40pxlinkedin_40